Archive for December, 2012

There you have it folks. Barry is going all in along with Feinstein and Biden’s blue ribbon committee. Now we must fight.

In the words of Micheal Bane “Join or die.”

BS

As intimidating as it looks the setup is relatively easy.  It took me roughly 2 hours but keep in mind that was taking picture breaks and helping my wife carry groceries into the house.

First step, we need to get it bolted down. Dillon recommends twelve inches of work space on each side.  Four 1/4 inch bolts are used to hold the press in place.

2012-12-30_12-00-26_741

Bolted down and rock solid.

Next step is to attach the cartridge collection bin bracket. This allows the completed cartridges to be ejected onto the chute and slide down into the bin.  You will need some wood screws or very small bolts to attach this directly to the bench.

2012-12-30_12-15-45_507

Here you can see the chute and collection bin

2012-12-30_12-15-27_882

A side view

After the bracket is set into place we need to apply the shellplate, the index ball and spring, the index sprocket, and set screw.

2012-12-30_12-32-10_867

All assembled it should look like this.

2012-12-30_12-32-18_930

With all the parts assembled you need to run the press to the top of its stroke and insert the set screw into the side of the shaft.

2012-12-30_12-32-32_437

Here you can almost see the set screw in this horrible blurry picture.

With the set screw tightened and the shell plate moving freely on the index ball we are on to tackling the priming system. First you need to know the kit comes set up for large primers. I will be setting mine up for 9mm and .223 so I needed the small primer bar installed (included) which added one extra step which, surprisingly this was much easier than I expected and the Dillon instruction manual outlines it really well. After the bar is installed you need to install the operating rod between the two white rollers. The kit includes an alarm for the primer tube that will sound when the tube becomes empty. Simply slipping it on to the tube and installing the battery completes this step.

2012-12-30_13-05-17_482

When completed the priming system should resemble this.

2012-12-30_13-06-08_816

Primer tube alarm

After this step the lower half of the press is completed. I added one step that wasnt in the Dillon instruction manual….. have the wife make cookies.

2012-12-30_13-04-23_407

mmmm…….. cookies

Starting with the upper half we need to get the dies into the toolhead. I didn’t add any good photos of the assembly of this since its pretty self explanatory. To get the dies adjusted properly refer to the instructions with your dies. Any standard 7/8 x 14 die will work with your Dillon press. For example, I am using Lee dies for my 9mm and RCBS for my .223 and both work fine.

The powder will be assembled by placing the powder measure on top of the die. A little trick is to leave the powder assembly a little loose on top of the die so it will be easier to adjust the die with it on top. After installing the powder bar, which is very simple and nearly self-explanatory, that is all that is left.  I haven’t tightened down my dies yet since I’m still waiting on my projectiles to show up.

2012-12-30_13-45-36_64

Finished up

Everything went smoothly and I didn’t run across anything the instruction manual didn’t cover. One thing I went out of my way to do was label my pickup tubes that are included with the kit. The tubes are color coded but I would rather read small or large on the tube then try to remember what color stands for what. I can’t wait for my projectiles to show up so I can get this thing rolling. As soon as I put around 1000 rounds through it I will be back with a full report and review on the function. Any questions between now and then just stick a comment on this post or send me an email and I will try to get you an answer as soon as possible.

BS

If you haven’t heard the news David Gregory on Meet The Press waved around an empty 30 round magazine on national TV. Not a big deal right? Well it wouldn’t be if your filming studios weren’t in Washington DC where you have some of the strictest gun laws in the country.

Our staunch anti-gun advocate friend David violated one of the very laws he intends to push onto all of the rest of the nation and it is imperitive that he pays for his crime. He ABSOLUTELY needs to feel what it is like to be on receiving end of the ignorant laws he pushes so hard for. But will justice be served?

Of course NBC is coming out stating Mr Gregory has a get out of jail free card (literally) from the ATF but the DC police are possibly saying other wise. The article in Politico here tries to spell out the situation. The DC police say they have an investigation ongoing so I believe it’s safe assume if they haven’t charged him with anything yet it is unlikely anything will come out of it.

BS

According to the New York Times.

Enjoy,
BS

Edit:
According to Everyday No Days Off it has been taken down and corrected.

I’m always trying to find the things that I feel are must reads and link to them for my readers. This is a few days old but I just ran across it and knew it was worth sharing.

http://backwoodshome.com/blogs/MassadAyoob/2012/12/21/understanding-both-sides/?utm_source=feedburner&utm_medium=feed&utm_campaign=Feed%3A+MassadAyoob+%28Massad+Ayoob%29

BS

Ron Paul’s take on Newtown

Posted: December 27, 2012 in Uncategorized
Tags: , ,

Not much to argure with here.

Thoughts or comments?

BS

Just the normal trampling of gun rights…….

http://www.feinstein.senate.gov/public/index.cfm/assault-weapons

BS